pp m - s ip - series C p pm xx - s ip - xx e lf C single output - plastic c ase specificat ion can change without a notice C we accept no liability for any inaccuracy or printing errors . page 1 / 3 ppmxx - s ip - xxelf all specifications typical at ta=25c, nominal input voltage and full load unless otherwise specified input specifications input voltage range 100 C 3 00 vdc or 85 C 264 vac * universal input current 40ma, typ. frequen cy 47 C 80 hz external input fuse (recommended) 1 a / 250 v * attention: for ac - input a capacitor between pin 7 and pin 10 is needed!! (see page 3) output specifications voltage accuracy 2% input variation 0.5% , typ. load variation (10 - 100%) 1% , typ. ripple and noise (20mhz bandwidth) 3.3 / 5 / 9 vdc models 12 vdc models 15 vdc models 24vdc models 100 mv pk - pk (50mv pk - pk typ.) 120mv pk - pk (60mv pk - pk typ.) 150mv pk - pk (75mv pk - pk typ.) 240mv pk - pk (120mv pk - pk typ.) short circui t protection continuous, auto recovery over temperature protection 150c, max. common specifications temperature range - 40 c to +85 c power derating 1 . 33 % / c (above 55c) case temperature +90c , max . storage - 40 c to +105 c humidity (non con densing) 85%, max. temperature coefficient 0.02%/c switching frequency 10 0khz, typ . i/o isolation voltage 2 000vac / 1min. leakage current none case material ul94v - 0 rated reliability calculated mtbf (mil - hdbk - 217f) > 300,000 hrs mainzer stra?e 151 C 153 d - 55299 nackenheim tel. +49 6135 7026 - 0 fax: +49 6135 931070 www. peak - electronics.de pe ak @peak - electronics.de the ppm - s ip - series are high efficiency gree n power modules with miniature packaging provided by peak . the features of this series are: wide input voltage, dc and ac all in one, high efficiency, high reliability, low loss, safety isolation etc. they are widely used in industrial, office and civil eq uipments , as well as applications where no special requirement for emc performance . it is recommended to add emi suppression circuit or take measure to shield when there is strict requirement for emc performance . p p m - s ip - series ? 1.65 - 3 watt ? univ. 100 - 3 00vdc / 85 - 264vac * ? s ingle output ? over temperature protection ? short circuit protection ? 2 kv ac i/o i solation ? high efficiency / density rev. 0 9 - 20 1 5
pp m - s ip - series C p pm xx - s ip - xx e lf C single output - plastic c ase specificat ion can change without a notice C we accept no liability for any inaccuracy or printing errors . page 2 / 3 selection guide package / pinning / derating ? 1.30 (0.051) order # power (w) output voltage (vdc) output current full load (ma) efficiency (%) single output ppm1.65-sip-3r3elf 1.65 3.3 500 70 ppm2.5-sip-05elf 2.5 5 500 70 PPM3-SIP-09ELF 3 9 330 75 ppm3-sip-12elf 3 12 250 78 ppm3-sip-15elf 3 15 200 78 ppm3-sip-24elf 3 24 125 78 if you need other specifications, please enquire. m a x . 2 5 . 5 0 ( 1 . 0 0 4 ) 1 1 2 m a x . 3 5 . 0 0 ( 1 . 3 8 ) 5 . 0 8 ( 0 . 2 0 ) 6 . 0 0 ( 0 . 2 3 6 ) 3 7 1 0 0 . 4 0 ( 0 . 0 1 6 ) 1 0 . 5 0 ( 0 . 4 1 3 ) m a x . p r i n t e d f a c e 0 . 8 4 ( 0 . 0 3 3 ) a l l d i m e n s i o n s a r e t y p i c a l i n m i l l i m e t e r s ( i n c h e s ) . - p i n s e c t i o n t o l e r a n c e : + / - 0 . 1 0 ( + / - 0 . 0 0 4 ) - c a s e t o l e r a n c e + / - 0 . 5 ( + / - 0 . 0 2 ) s p e c i f i c a t i o n m a y c h a n g e w i t h o u t n o t i c e . s i p C a c / d c b a c k s i d e 2 2 . 8 6 ( 0 . 9 0 ) 1 2 . 7 0 ( 0 . 5 0 ) # single 1 +vout 3 - vout 7 - vin 10 cap 12 +vin pin connections 40 100 60 80 load(%) temperature( c) -20 55 85 -40
pp m - s ip - series C p pm xx - s ip - xx e lf C single output - plastic c ase specificat ion can change without a notice C we accept no liability for any inaccuracy or printing errors . page 3 / 3 app notes: structure figure anear measure note: c1: 1f (ceramic capacitor) c2: 10f (electrolytic capacitor) typical application fig. 1: standard fig. 2: this applic ation is not supported for this series. fig. 3: ppm - sip - series recommended circuit for application require higher emc standard (external circuit output same as above) external capacitor typical value output voltage c1 c2 c 3 fuse tvs 3.3v 10f/400v 1 f/ 5 0 v 1 50f/25 v 1 a/250v smbj7.0a 5v 9v smbj12a 12v smbj20a 15v 100f/35v 24v smbj30a note: 1. c1: ac input , is a filtering electrolytic capacitor , which is required when input voltage is below 100vac, and the value of c1 is 22 f/400v. dc input , is a filtering capacitor in emc filter, the value of c1 is 10 f /400v (when input voltage is above 2 70vdc , and the value of c1 is 10 f/450v), if emc performance is not required, c1 could not need. 2. c2 is ceramic capacitor, it is used to filter high frequency noise. output filtering capacitor c3 (which is required by ac input or dc input) is recommended to use high frequency and low imp edance electrolytic capacitors. voltage derating of capacitor should be 80% or above. tvs is a recomm ended component to protect post - circuits (if converter fails). 3. recommended external circuit parameters in figure 3: mov: varistor, model: 561kd14 it is used to protect the device under surge; r1 r2 2 /3w winding resistor r3 1m /2w cy cy1 cy2 cy3 cy4 102m/400vac cx 0.22f/275vac lcm 10mh - 30mh ldm 300 h 4. fuse 1a/250v slow - blow attention: for ac - input a capacitor (10uf/400v) between pin 7 and pin 10 is needed!! dc/dc convertor +vin(l) -vin(n) + c1 e xternal capacitor 12 7 10 1 3 rectificate contrl circuit f eedback loop voltage sampling rectifier filter circuit +vo -vo copper sheet load connect oscillograph probe fuse l n c2 c3 7 + vo - vo tvs rl 3 1 l n c1 + 10 + cy 12 fuse ntc mov l n +vo -vo ac-dc l n +vo -vo output n l n l pe lcm mov r2 r1 r3 cx cy3 cy4 a c d c cy1 cy2 c1 + 10 cy ldm can use mor n s u n s fc -l01d fuse
|
